HD74LSP Specifications: Gate Type: NAND ; Supply Voltage: 5V ; Logic Family: TTL ; Inputs: 8 Details, datasheet, quote on part number: HD74LSP . The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas. Technology Corporation on April 1st HD74LSP from Renesas Electronics. Find the PDF Datasheet, Specifications and Distributor Information.

Author: Yozshujinn Nikotaur
Country: Nicaragua
Language: English (Spanish)
Genre: Finance
Published (Last): 16 February 2013
Pages: 163
PDF File Size: 13.85 Mb
ePub File Size: 11.73 Mb
ISBN: 383-5-23768-184-9
Downloads: 51417
Price: Free* [*Free Regsitration Required]
Uploader: Shale

Check AC Cord and Replace. This allows decoded dqtasheet unused sections of memory to be used by the cartridge hardware. This allows the two oscillator to be divided down to the datasheeg frequency of Doing so can save hours of troubleshooting time only to find out that a cable was bad, or that it was some other relatively minor problem.

Some printers will require that these assumptions be modified. The prior written approval of Renesas Technology Corp. Whenever a cartridge is inserted into the computer, this input will interrupt BASIC and jump hdd74ls374p the program in the cartridge. The Namefile block is standard block with a length of 15 bytes OFH.

PIA Block Diagram 39 These shields must be in place to provide proper RFI shielding. This signal is provided to the video output terminal through buffer Q2, Q3 and to the modulator.

Remove the top cabinet as described in 3. The secondary of the power transformer provides When power is applied to the CPU, it immediately attempts to fetch a vector and begin executing instructions. Burst Start Position adjustment Connection: The TV antenna is attached directly to the switch box. Pin 11 of register B is the single-bit sound hf74ls374p. Any greater signal amplitude will result in clipping distortion of the sound waveform. Due to the nature of the ROMs and in order to prevent data bus contention, datashfet ROMs are enabled only during the E portion of a read cycle.


HD74LSP pdf Datasheet P1 Part Num IC-ON-LINE

When the incoming signal goes high, the transistor becomes saturated and connects its end of the cassette relay to ground, causing the relay to energize. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and. According to the above table, different sound sources are selected by the Sel A and Sel B inputs, and the selected input is routed datqsheet the sound output.

After the problem is localized, isolating it to a specific component is usually not very difficult. The is connected ider part of f 4 is used to to This output is coupled through a ohm resistor, R15 to the output connector.

One block type byte: RSC Connector Pinout 48 I Mfr’s Part No. These are the RGB values.


The switch is specially designed to provide the 60 dB of isolation required between the computer and the TV antenna. CA2 is an output used to control the cassette motor.


Ensure that the power cord is properly routed to afford strain datqsheet to the transformer connections. This tells the computer that the printer is ready all of the time. The ones used by the Color Computer 3 are: The most common usage of the cartridge connector is with the ROM cartridge. H Pi] KCJ -?? It is used to detect the presence of a cartridge.

Two bytes for the start address of a machine language program 6. Replace despike capacitor for that chip NTSC 6.

The mechanical assembly allows both potentiometers to be changed at the same time. For this purpose, the internal oscillator circuit of the IC is used. The control registers also handle device selection within the PIA. The actual time depends on the access time of the DRAM.

The switch box is connected to the customer’s TV through the ohm twin-lead output. The data format is one start bit, eight data bits, two stop bits, and no parity. Although Tandy f s computer cassette recorders do not produce more than 6 volts p-p, the circuitry is protected from voltages as high as 18 volts p-p. Disconnect the cable from the wire connector which is attached to the keyboard Figure Figure shows the complete power supply datazheet.